1) The objectives of this Code are achieved by measures, such as those described in
the acceptable solutions in Division B, that are intended to allow the
building or its elements to perform the following functions (see
Appendix A):
F01 To minimize the risk of accidental ignition.
F02 To limit the severity and effects of fire or
explosions.
F03 To retard the effects of fire on areas beyond its point of
origin.
F04 To retard failure or collapse due to the effects of
fire.
F05 To retard the effects of fire on emergency egress
facilities.
F06 To retard the effects of fire on facilities for notification,
suppression and emergency response.
F10 To facilitate the timely movement of persons to a safe place in an
emergency.
F11 To notify persons, in a timely manner, of the need to take action in
an emergency.
F12 To facilitate emergency response.
F13 To notify emergency responders, in a timely manner, of the need to
take action in an emergency.
F20 To support and withstand expected loads and forces.
F21 To limit or accommodate dimensional change.
F22 To limit movement under expected loads and forces.
F23 To maintain equipment in place during structural
movement.
F30 To minimize the risk of injury to persons as a result of tripping,
slipping, falling, contact, drowning or collision.
F31 To minimize the risk of injury to persons as a result of contact
with hot surfaces or substances.
F32 To minimize the risk of injury to persons as a result of contact
with energized equipment.
F33 To limit the level of sound of a fire alarm system.
F34 To resist or discourage unwanted access or entry.
F35 To facilitate the identification of potential
intruders.
F36 To minimize the risk that persons will be trapped in confined
spaces.
F40 To limit the level of contaminants.
F41 To minimize the risk of generation of contaminants.
F42 To resist the entry of vermin and insects.
F43 To minimize the risk of release of hazardous
substances.
F44 To limit the spread of hazardous substances beyond their point of
release.
F46 To minimize the risk of contamination of potable water.
F50 To provide air suitable for breathing.
F51 To maintain appropriate air and surface temperatures.
F52 To maintain appropriate relative humidity.
F53 To maintain appropriate indoor/outdoor air pressure
differences.
F54 To limit drafts.
F55 To resist the transfer of air through environmental
separators.
F60 To control the accumulation and pressure of water on and in the
ground.
F61 To resist the ingress of precipitation, water or moisture from the
exterior or from the ground.
F62 To facilitate the dissipation of water and moisture from the
building.
F63 To limit moisture condensation.
F70 To provide potable water.
F71 To provide facilities for personal hygiene.
F72 To provide facilities for the sanitary disposal of human and
domestic wastes.
F73 To facilitate access to and circulation in the
building and its facilities by persons with physical or sensory limitations (see
Sentence 3.1.1.2.(3) for application limitation).
F74 To facilitate the use of the
building's facilities by persons with physical or sensory limitations (see
Sentence 3.1.1.2.(3) for application limitation).
F80 To resist deterioration resulting from expected service
conditions.
F81 To minimize the risk of malfunction, interference, damage,
tampering, lack of use or misuse.
F82 To minimize the risk of inadequate performance due to improper
maintenance or lack of maintenance.
F83 
To control the amount of water a plumbing fixture will use.
F84 To control the flow of water to a plumbing fixture or outlet.
F85 To minimize thermal loss or gain.
F86 To minimize the use of energy for building systems.
F90 To limit the amount of uncontrolled air leakage through the
building envelope.
F91 To limit the amount of uncontrolled air leakage through system components.
F92 To limit the amount of uncontrolled thermal transfer through the
building envelope.
F93 To limit the amount of uncontrolled thermal transfer through system components.
F95 To limit the unnecessary demand or consumption of energy for heating and cooling.
F96 To limit the unnecessary demand or consumption of energy for service water heating.
F98 To limit the inefficiency of equipment.
F99 To limit the inefficiency of systems.
F100 To limit the unnecessary rejection of reusable waste energy.
BC2012 2013-04-03 R2NC2010 2010-01-01 R1
1) The objectives of this Code are achieved by measures, such as those described in
the acceptable solutions in Division B, that are intended to allow the
building or its elements to perform the following functions
(see Appendix A):
F01 To minimize the risk of accidental ignition.
F02 To limit the severity and effects of fire or
explosions.
F03 To retard the effects of fire on areas beyond its point of
origin.
F04 To retard failure or collapse due to the effects of
fire.
F05 To retard the effects of fire on emergency egress
facilities.
F06 To retard the effects of fire on facilities for notification,
suppression and emergency response.
F10 To facilitate the timely movement of persons to a safe place in an
emergency.
F11 To notify persons, in a timely manner, of the need to take action in
an emergency.
F12 To facilitate emergency response.
F13 To notify emergency responders, in a timely manner, of the need to
take action in an emergency.
F20 To support and withstand expected loads and forces.
F21 To limit or accommodate dimensional change.
F22 To limit movement under expected loads and forces.
F23 To maintain equipment in place during structural
movement.
F30 To minimize the risk of injury to persons as a result of tripping,
slipping, falling, contact, drowning or collision.
F31 To minimize the risk of injury to persons as a result of contact
with hot surfaces or substances.
F32 To minimize the risk of injury to persons as a result of contact
with energized equipment.
F33 To limit the level of sound of a fire alarm system.
F34 To resist or discourage unwanted access or entry.
F35 To facilitate the identification of potential
intruders.
F36 To minimize the risk that persons will be trapped in confined
spaces.
F40 To limit the level of contaminants.
F41 To minimize the risk of generation of contaminants.
F42 To resist the entry of vermin and insects.
F43 To minimize the risk of release of hazardous
substances.
F44 To limit the spread of hazardous substances beyond their point of
release.
F46 To minimize the risk of contamination of potable water.
F50 To provide air suitable for breathing.
F51 To maintain appropriate air and surface temperatures.
F52 To maintain appropriate relative humidity.
F53 To maintain appropriate indoor/outdoor air pressure
differences.
F54 To limit drafts.
F55 To resist the transfer of air through environmental
separators.
F56 To limit the transmission of airborne sound into a dwelling unit from spaces elsewhere in the building (see Sentence 3.1.1.2.(2) for application limitation).
F60 To control the accumulation and pressure of water on and in the
ground.
F61 To resist the ingress of precipitation, water or moisture from the
exterior or from the ground.
F62 To facilitate the dissipation of water and moisture from the building.
F63 To limit moisture condensation.
F70 To provide potable water.
F71 To provide facilities for personal hygiene.
F72 To provide facilities for the sanitary disposal of human and
domestic wastes.
F73 To facilitate access to and circulation in the building and its facilities by persons with physical or sensory
limitations (see Sentence 3.1.1.2.(3) for application
limitation).
F74 To facilitate the use of the building's
facilities by persons with physical or sensory limitations (see Sentence 3.1.1.2.(3) for application
limitation).
F80 To resist deterioration resulting from expected service
conditions.
F81 To minimize the risk of malfunction, interference, damage,
tampering, lack of use or misuse.
F82 To minimize the risk of inadequate performance due to improper
maintenance or lack of maintenance.
F83 To control the amount of water a plumbing fixture will use.
F84 To control the flow of water to a plumbing fixture or outlet.
F85 To minimize thermal loss or gain.
F86 To minimize the use of energy for building systems.
F90 To limit the amount of uncontrolled air leakage through the building envelope.
F91 To limit the amount of uncontrolled air leakage through system components.
F92 To limit the amount of uncontrolled thermal transfer through the building envelope.
F93 To limit the amount of uncontrolled thermal transfer through system components.
F95 To limit the unnecessary demand or consumption of energy for heating and cooling.
F96 To limit the unnecessary demand or consumption of energy for service water heating.
F98 To limit the inefficiency of equipment.
F99 To limit the inefficiency of systems.
F100 To limit the unnecessary rejection of reusable waste energy.
1) The objectives of this Code are achieved by measures, such as those described in
the acceptable solutions in Division B, that are intended to allow the
building or its elements to perform the following functions
(see Appendix A):
F01 To minimize the risk of accidental ignition.
F02 To limit the severity and effects of fire or
explosions.
F03 To retard the effects of fire on areas beyond its point of
origin.
F04 To retard failure or collapse due to the effects of
fire.
F05 To retard the effects of fire on emergency egress
facilities.
F06 To retard the effects of fire on facilities for notification,
suppression and emergency response.
F10 To facilitate the timely movement of persons to a safe place in an
emergency.
F11 To notify persons, in a timely manner, of the need to take action in
an emergency.
F12 To facilitate emergency response.
F13 To notify emergency responders, in a timely manner, of the need to
take action in an emergency.
F20 To support and withstand expected loads and forces.
F21 To limit or accommodate dimensional change.
F22 To limit movement under expected loads and forces.
F23 To maintain equipment in place during structural
movement.
F30 To minimize the risk of injury to persons as a result of tripping,
slipping, falling, contact, drowning or collision.
F31 To minimize the risk of injury to persons as a result of contact
with hot surfaces or substances.
F32 To minimize the risk of injury to persons as a result of contact
with energized equipment.
F33 To limit the level of sound of a fire alarm system.
F34 To resist or discourage unwanted access or entry.
F35 To facilitate the identification of potential
intruders.
F36 To minimize the risk that persons will be trapped in confined
spaces.
F40 To limit the level of contaminants.
F41 To minimize the risk of generation of contaminants.
F42 To resist the entry of vermin and insects.
F43 To minimize the risk of release of hazardous
substances.
F44 To limit the spread of hazardous substances beyond their point of
release.
F46 To minimize the risk of contamination of potable water.
F50 To provide air suitable for breathing.
F51 To maintain appropriate air and surface temperatures.
F52 To maintain appropriate relative humidity.
F53 To maintain appropriate indoor/outdoor air pressure
differences.
F54 To limit drafts.
F55 To resist the transfer of air through environmental
separators.
F56 To limit the transmission of airborne sound into a dwelling unit from spaces elsewhere in the building (see Sentence 3.1.1.2.(2) for application limitation).
F60 To control the accumulation and pressure of water on and in the
ground.
F61 To resist the ingress of precipitation, water or moisture from the
exterior or from the ground.
F62 To facilitate the dissipation of water and moisture from the building.
F63 To limit moisture condensation.
F70 To provide potable water.
F71 To provide facilities for personal hygiene.
F72 To provide facilities for the sanitary disposal of human and
domestic wastes.
F73 To facilitate access to and circulation in the building and its facilities by persons with physical or sensory
limitations (see Sentence 3.1.1.2.(3) for application
limitation).
F74 To facilitate the use of the building's
facilities by persons with physical or sensory limitations (see Sentence 3.1.1.2.(3) for application
limitation).
F80 To resist deterioration resulting from expected service
conditions.
F81 To minimize the risk of malfunction, interference, damage,
tampering, lack of use or misuse.
F82 To minimize the risk of inadequate performance due to improper
maintenance or lack of maintenance.
F83 To control the amount of water a plumbing fixture will use.
F84 To control the flow of water to a plumbing fixture or outlet.
F85 To minimize thermal loss or gain.
F86 To minimize the use of energy for building systems.
F90 To limit the amount of uncontrolled air leakage through the building envelope.
F91 To limit the amount of uncontrolled air leakage through system components.
F92 To limit the amount of uncontrolled thermal transfer through the building envelope.
F93 To limit the amount of uncontrolled thermal transfer through system components.
F95 To limit the unnecessary demand or consumption of energy for heating and cooling.
F96 To limit the unnecessary demand or consumption of energy for service water heating.
F98 To limit the inefficiency of equipment.
F99 To limit the inefficiency of systems.
F100 To limit the unnecessary rejection of reusable waste energy.